• 電池實驗設備
    您當前的位置 : 首 頁 > 資訊動態 > 技術資訊

    皮帶輸送機傳動鏈條發生故障的幾種表現形式

    2020-12-21

      

    皮帶輸送機傳動鏈條發生故障的幾種表現形式

       輸送流水線:輸送鏈條應該是最常見的一種工業鏈條。在工業生產過程中,尤其是在很多的食品加工中,輸送機鏈條均以流水線的方式使用,使用范圍廣、使用頻率高,因此也常常會發生磨損的故障,如果再加之使用方法的不當,會對鏈條造成極大的損傷。

      Conveying assembly line: Conveying chain should be the most common kind of industrial chain. In the industrial production process, especially in many food processing, conveyor chains are used in an assembly line, with a wide range of use and high frequency of use. Therefore, wear failures often occur. If the use method is improper, Will cause great damage to the chain.

    滾筒流水線、皮帶流水線、組裝流水線等都是工業生產車間內最常見的幾種。不同的生產工藝流程,應選擇適合的流水線設備。才能在提高生產效率的同時,讓它的價值充分地體現出來。針對前面的幾種流水線,在使用之前,它的安裝工作是非常重要的,這是直接影響到它的使用效果的。那如何正確地安裝滾筒流水線呢?下面跟著小編一走來了解一下吧。

      Roller assembly lines, belt assembly lines, and assembly lines are the most common types in industrial production workshops. For different production processes, suitable assembly line equipment should be selected. In order to improve production efficiency, its value can be fully reflected. For the previous several kinds of assembly lines, its installation work is very important before use, which directly affects its use effect. Then how to install the drum assembly line correctly? Let's follow the editor to find out.

    UV機.jpg

      一、鋪設走線槽,連接各傳輸單元氣源。將傳輸線體找正操平。電氣、電源線信號安裝。

      1. Lay the wiring trough and connect the air source of each transmission unit. Align and level the transmission line body. Electrical and power line signal installation.

    場地定位(作標記) 流水線架子安裝大腳體,在已定位好的場地上按次序擺放連接桿。

      2. Site positioning (marking) The assembly line rack is installed with large feet, and the connecting rods are placed in order on the site that has been positioned.

      三、在護板上安裝電動刀插座(24V)、保險絲、掛鉤,并且接電動刀插座與白先絲之間的電線,注意電動刀插座方向,有凸起邊向下。

      3. Install the electric knife socket (24V), fuse and hook on the guard plate, and connect the electric wire between the electric knife socket and the white wire. Pay attention to the direction of the electric knife socket, with the raised side facing downward.

      四、安裝護板前在流水線架子護板安裝位臵上用5mm螺紋轉打螺紋,安裝走線槽、護板, 放走線槽電線和接220V插座。

      4. Before installing the guard plate, use 5mm thread to turn the thread on the installation position of the assembly line shelf guard plate, install the wire trough, guard plate, release the wire trough wire and connect to the 220V socket.

      五、線體調平,可以采用建筑線調平,調平高度可為0.625m,安裝走線槽蓋并用膠帶固定。


      5. Line body leveling can be leveled by building line, the leveling height can be 0.625m, install the cable trough cover and fix it with tape.


    標簽

    最近瀏覽:

    CONTACT US

    聯系我們

    手機:13712926617

    座機:0752-6811300

    郵箱:lujinxin304205@163.com

    地址:博羅縣園洲鎮梁屋高頭村興發路86號南面



    ATTENTION

    關注我們

    皮帶輸送線

    掃一掃,咨詢

    在厨房边吃饭边做的日本电影